K-Tech

How to Make a Slow Computer and Laptops Run Faster Using SSD ard Disk 1000% Working in Tamil

If You Have Old Laptops ,It's Very Slow Don't wory Easy To Run Faster like 10x Speed Using SSD "Solide State Drive".
If your laptop has a hard drive (HDD), consider changing it for a solid state drive (SSD). An SSD can speed up your everyday tasks by up to six times.

Solid-state drives (SSDs) are the most common storage drives today. SSDs are smaller and faster than hard disk drives (HDDs). SSDs are noiseless and allow PCs to be thinner and more lightweight. Hard disk drives (HDDs) are more common in older devices.
SSDs store data permanently inside an integrated circuit, typically using flash memory. The flash memory inside an SSD means data is written, transferred, and erased electronically and silently.
SSDs are faster, more durable, more compact, quieter, and consume less energy.
Increase speed and storage capacity to desktops and laptops with an SSD.

How to Make a Slow Computer and Laptops Run Faster Using SSD ard Disk 1000% Working in Tamil

Comments

AX2358 Homemade 5.1 Remote Kit with 16x2 LCD

AX2358 Homemade 5.1 Remote Kit with 16x2 LCD AX2358 is I used for this 5.1 remote kit project. It is Built-in 2-channel to 6-channel converter and 6-channel volume controller. It has 4 stereo inputs and one 6 channel input. Any stereo input terminals of AX2358 are selected, it will be directly converted to 6 channels and then output through volume adjustment but when the signal from the 6-channel input terminal is selected, it directly enters the volume adjustment and then outputs it without any processing. It has 6-channel individual volume control in this IC (0 to -79dB, 1dB/step). This IC working by I2C communication. The data are transmitted to the AX2358 via the SDA and SCL. So I need a microcontroller. I choose the microcontroller is Atmega328 for this. This microcontroller programmed with Arduino UNO. ...

DIY Tutorial Resetting Toner Chip on Ricoh SP C250DN Printer in Simple Steps

DIY Tutorial Resetting Toner Chip on Ricoh SP C250DN Printer in Simple Steps The RICOH SP 250DN printer toners have a chip that keeps track of the number of pages that have been printed. This is anoying because it will render a refill useless. In order to reuse this kind of toner, there are two things you need to do: refill the toner with ink (if needed) reset the toner chip (or replace it) There is plenty of information explaining how to refill the toner but little information on how to erase the toner chip. This document deals with the second point: how to dump the chip and reset it. It took me a while to get everything setup and to have my toner chip reset so I would like to share this process in order to help other to do the same with their printer toner cartridges. I will step through the process of understanding the problem, analysing the chip circuit, dumping the chip contents and writing back a pattern so the printer will be able to initialize the chip and set t...

DIY Metal Detector using Arduino A Simple Guide to Building Your Own at Home

DIY Metal Detector using Arduino A Simple Guide to Building Your Own at Home How does a metal detector work? As we can see there are three things that are using to complete the whole project. Electronic circuit, Arduino, and a copper coil. here actually we are making a proximity sensor that detects the metal with a metal detector using Arduino . Here are the steps to build a DIY metal detector using an Arduino: Materials required: Arduino UNO Copper coil Diode 10nf capacitor Buzzer Led 220 ohm & 330 Ohm Resistor Jumper wires and a breadboard USB cable for uploading the code Circuit Diagram Arduino metal detector:- Arduino UNO 10 nf Capacitor A2 Pin Terminal 1 GND Terminal 2 Arduino UNO Buzzer D6 Pin Positive GND Negative Arduino LED 220 Ohm Resistor D5 Pin Terminal 1 Anode Pin Terminal 2 GND Cathode Pin Arduino UNO Copper coil Diode 330-ohm res Terminal 1 Terminal 1 Terminal 1 A1 Pin Terminal 2 A2 Pin ...

How to Calculate Inverter Battery Backup Time

How to Calculate Inverter Battery Backup Time? Backup Time (in hours) = Battery Capacity (in Ah) X Input voltage (V) / Total Load (in Watts) Whenever you plan to buy an inverter battery, there is a desire to know some important information in your mind. Like how much will be the backup of the inverter battery, how many hours of backup will be available for how many ah batteries, etc. In this informative information, here you will know the backup time calculation formula. Taking your inputs, you can calculate your total load, like: 3 tube led lights = 40 x 3 = 120 Watts 2 fans = 75 x 2 = 150 Watts 1 Bulb router = 1×20 Watts = 20 Watts So, the total load in your case is 120 + 150 + 20 = 290 Watts. Now, let us apply all these values in the above-said battery backup time formula. Backup Time (in hours) = Battery Capacity (in Ah) X Input voltage (V) / Total Load (in Watts) Backup Time (in hours) = 150 x 12 / 290 = 6.2 So, your inverter battery will last around 6.2 hours ....

Wireless Joystick controlled Robot Car using Arduino, 433Mhz RF and L298N Motor Driver

Wireless Joystick controlled Robot Car using Arduino – In this tutorial, you will learn how to control a Robot Car wirelessly using Arduino, L298N Motor driver, and 433 Mhz RF transmitter and Receiver . The robot control system can be activated and de-activated using the Built-in Joystick push Button. Arduino Uno Arduino Nano Mega 2560: Robot Car chassis kit: L298N motor driver: 2-Axis Analog Joystick 433 MHz Transmitter and Receiver Modules: DISCLAIMER: Please Note: these are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way! wireless joystick Interfacing: Watch this tutorial for the robot parts assembling and connections. All the connections are exactly the same as explained in my previous tutorial. The only modification that I did is the addition of the 433 Mhz RF receiver module…the VCC pin of the receiver module is connected with the 5 volts…the ground pin of the ...